View DS1267S-100TR_8864177.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 12 102199 vb nc h1 l1 w1 rst clk gnd 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 v cc nc s out w0 h0 l0 c out dq 16-pin soic (300-mil) see mech. drawings section features ultra-low power consumption, quiet, pumpless design two digitally controlled, 256-position potentiometers serial port provides means for setting and reading both potentiometers resistors can be connected in series to provide increased total resistance 14-pin dip, 16-pin soic, 20-pin tssop packages resistive elements are temperature compensated to 0.3 lsb relative linearity standard resistance values: ? ds1267-10 ~ 10 k w ? ds1267-50 ~ 50 k w ? ds1267-100 ~ 100 k w operating temperature range: ? industrial: -40c to +85c pin assignment pin descriptions l0, l1 - low end of resistor h0, h1 - high end of resistor w0, w1 - wiper terminal of resistor v b - su bstrate bias voltage s out - stacked configuration output rst - serial port reset input dq - serial port data input clk - serial port clock input c out - cascade port output v cc - +5 volt supply gnd - ground nc - no internal connection 14-pin dip (300-mil) see mech. drawings section vb h1 l1 w1 rst clk gnd 14 13 12 11 10 9 8 1 2 3 4 5 6 7 v cc s out w0 h0 l0 c out dq ds1267 dual digital potentiometer chip www.dalsemi.com 20-pin tssop (173-mil) vb nc h1 l1 w1 rst clk 20 19 18 17 16 15 14 1 2 3 4 5 6 7 v cc nc nc s out w0 h0 l0 8 9 10 13 12 11 c out nc nc nc gnd dq downloaded from: http:///
ds1267 2 of 12 102199 description the ds1267 dual digital potentiometer chip consists of two digitally controlled, solid-state potentiometers. each potentiometer is composed of 256 resi stive sections. between each resistive section and both ends of the potentiometer are tap points which are accessible to the wiper. the position of the wiper on the resistive array is set by an 8-bit value that controls which tap point is connected to the wiper output. communication and control of the device are acco mplished via a 3-wire serial port interface. this interface allows the device wiper position to be read or written. both potentiometers can be connected in series (or st acked) for an increased total resistance with the same resolution. for multiple-device, single-processor en vironments, the ds1267 can be cascaded or daisy-chained. this feature provides for control of mult iple devices over a single 3-wire bus. the ds1267 is offered in three standard resistance values which include 10, 50, and 100-kohm versions. available packages for the device include a 14-pin dip, 16-pin soic, and 20-pin tssop. operation the ds1267 contains two 256-position potentiometers whose wi per positions are set by an 8-bit value. these two 8-bit values are written to a 17-bit i/o shif t register that is used to store the two wiper positions and the stack select bit when the device is powered. a b lock diagram of the ds1267 is presented in figure 1. communication and control of the ds1267 are accomplished th rough a 3-wire serial port interface that drives an internal control logic unit. the 3-wire seria l interface consists of the three input signals: rst , clk, and dq. the rst control signal is used to enable the 3-wire serial port operation of the device. the chip is selected when rst is high; rst must be high to begin any communication to the ds1267. the clk signal input is used to provide timing synchronization for data input and output. the dq signal line is used to transmit potentiometer wiper settings and the sta ck select bit configuration to the 17-bit i/o shift register of the ds1267. figure 9(a) presents the 3-wire serial port protocol. as s hown, the 3-wire port is inactive when the rst signal input is low. communication with the ds1267 requires t he transition of the rst input from a low state to a high state. once the 3-wire port has been a ctivated, data is entered into the part on the low to high transition of the clk signal inputs. three-wire se rial timing requirements are provided in the timing diagrams of figure 9(b)-(c). data written to the ds1267 over the 3-wire serial interface i s stored in the 17-bit i/o shift register (see figure 2). the 17-bit i/o shift register contains both 8-b it potentiometer wiper position values and the stack select bit. the composition of the i/o shift re gister is presented in figure 2. bit 0 of the i/o shift register contains the stack select bit, which will be discussed in the section entitled "stacked configuration." bits 1 through 8 of the i/o shift register contain the potentiometer-1 wiper position value. bit 1 contains the msb of the wiper setting for potenti ometer-1 and bit 8 the lsb for the wiper setting. bits 9 through 16 of the i/o shift register contain the v alue of the potentiometer-0 wiper position, with the msb for the wiper position occupying bit 9 and the lsb bit 16. downloaded from: http:///
ds1267 3 of 12 102199 ds1267 block diagram figure 1 i/o shift register figure 2 transmission of data always begins with the stack sele ct bit followed by the potentiometer-1 wiper position value and lastly the potentiometer-0 wiper position value. when wiper position data is to be written to the ds1267, 17 bits (or some integer multiple) of data should always be transmitted. transactions which do not send a complete 17-bits (or multiple) will leave the register incomplete and possibly an error in the desired wiper positions. after a communication transaction has been completed, the rst signal input should be taken to a low state to prevent any inadvertent changes to the device shift register. once rst has reached a low state, the contents of the i/o shift register are loaded into the respective multiplexers for setting wiper position. a new wiper position will only engage after a rst transition to the inactive state. on device power-up the ds1267 wiper positions will be set at 50% of the total resistance or binary value 1000 0000. downloaded from: http:///
ds1267 4 of 12 102199 stacked configuration the potentiometers of the ds1267 can be connected in seri es as shown in figure 3. this is referred to as the stacked configuration. the stacked configuration allows the user to double the total end-to-end resistance of the part and the number of steps to 512 (or 9 bits of resolution). the wiper output for the combined stacked potentiometer wil l be taken at the s out pin, which is the multiplexed output of the wiper of potentiometer-0 (w0) or pot entiometer-1 (w1). the potentiometer wiper selected at the s out output is governed by the setting of the stack select bit (bit 0) of the 17-bit i/o shift register. if the stack select bit has value 0, th e multiplexed output, s out , will be that of the potentiometer-0 wiper. if the stack select bit has value 1, the multiplexed output, s out , will be that of the potentiometer-1 wiper. stacked configuration figure 3 cascade operation a feature of the ds1267 is the ability to control multiple devices from a single processor. multiple ds1267s can be linked or daisy-chained as shown in figure 4. a s a data bit is entered into the i/o shift register of the ds1267 a bit will appear at the c out output within a maximum delay of 50 nanoseconds. the stack select bit of the ds1267 will always be the fi rst out the part at the beginning of a transaction. additionally the c out pin is always active regardless of the state of rst . this allows one to read the i/o shift register without changing its value. cascading multiple devices figure 4 downloaded from: http:///
ds1267 5 of 12 102199 the c out output of the ds1267 can be used to drive the dq input of anoth er ds1267. when connecting multiple devices, the total number of bits transmitted i s always 17 times the number of ds1267s in the daisy chain. an optional feedback resistor can be placed between the c out terminal of the last device and the first ds1267 dq input, thus allowing the controlling processor to r ead as well as write data or circularly clock data through the daisy chain. the value of the feedback or isolation resistor should be in the range from 1 to 10 kohms. when reading data via the c out pin and isolation resistor, the dq line is left float ing by the reading device. when rst is driven high, bit 17 is present on the c out pin, which is fed back to the input dq pin through the isolation resistor. when the clk input t ransitions low to high, bit 17 is loaded into the first position of the i/o shift register and bit 16 beco mes present on c out and dq of the next device. after 17 bits (or 17 times the number of ds1267s in the daisy chain ), the data has shifted completely around and back to its original position. when rst transitions to the low state to end data transfer, t he value (the same as before the read occurred) is loaded into the wipe r-0, wiper-1, and stack select bit i/o register. absolute and relative linearity absolute linearity is defined as the difference between the actual measured output voltage and the expected output voltage. figure 5 presents the test circuit use d to measure absolute linearity. absolute linearity is given in terms of a minimum increment or expected output when the wiper is moved one position. in the case of the test circuit, a minimum i ncrement (mi) or one lsb would equal 10/512 volts. the equation for absolute linearity is given as follows : (1) absolute linearity al={v o (actual) - v o (expected)}/mi relative linearity is a measure of error between two adjacent wiper position points and is given in terms of mi by equation (2). (2) relative linearity rl={v o (n+1) - v o (n)}/mi figure 6 is a plot of absolute linearity and relative lin earity versus wiper position for the ds1267 at 25c. the specification for absolute linearity of the ds1267 is 0.75 mi typical. the specification for relative linearity of the ds1267 is 0.3 mi typical. downloaded from: http:///
ds1267 6 of 12 102199 linearity measurement configuration figure 5 note: in this setup, a 2% delta in total resistance r0 to r1 w ould cause a 2.5 mi error. ds1267 absolute and relative linearity figure 6 typical application configurations figures 7 and 8 show two typical application configurations f or theds1267. by connecting the wiper terminal of the part to a high-impedance load, the effec ts of the wiper resistance is minimized, since the wiper resistance can vary from 400 to 1000ohms depending on wipe r voltage. figure 7 presents the device connected in an inverting variable gain amplifier . the gain of the circuit on figure 7 is given by the following equation: av = -n/(255-n); where n = 0 to 255 figure 8 shows the device operating in a fixed gain attenuat or where the potentiometer is used to attenuate an incoming signal. note the resistance r1 is chosen to be much greater than the wiper resistance to minimize its effect on circuit gain. downloaded from: http:///
ds1267 7 of 12 102199 inverting variable gain amplifier figure 7 fix gain attenuator figure 8 downloaded from: http:///
ds1267 8 of 12 102199 absolute maximum ratings* voltage on any pin relative to ground (vb=gnd) -0.1v to +7.0v voltage on resistor pins when vb=-5.5v -5.5v to +7.0v voltage on v b -5.5v to gnd operating temperature -40 to +85c storage temperature -55c to +125c soldering temperature 260c for 10 sec onds * this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this speci fication is not implied. exposure to absolute maximum rating conditions for extended periods of time may affect reliability. recommended dc operating conditions (-40 c to +85 c; v cc =5.0v 10%) parameter symbol min typ max units notes supply voltage v cc 4.5 5.5 v 1 input logic 1 v ih 2.0 v cc +0.5 v 1 input logic 0 v il -0.5 +0.8 v 1 substrate bias v b -5.5 gnd v 1 resistor inputs l,h,w v b -0.5 v cc +0.5 v 2 dc electrical characteristics (-40 c to +85 c; v cc = 5.0v 10%) parameter symbol min typ max units notes supply current i cc 22 650 a 9 input leakage i li -1 +1 a wiper resistance r w 400 1000 w 5 wiper current i w 1 ma output leakage i lo -1 +1 a logic 1 output @ 2.4v i oh -1 ma 7 logic 0 output @ 0.4v i ol 4 ma 7 standby current i stby 22 a 5 downloaded from: http:///
ds1267 9 of 12 102199 analog resistor characteristics (-40 c to +85 c; v cc = 5.0v 10%) parameter symbol min typ max units notes end-to-end resistor tolerance -20 +20 % 10 absolute linearity .75 ldb 3 relative linearity 0.3 ldb 4 -3 db cutoff frequency f cutoff hz 6 temperature coefficient 750 ppm/c capacitance (t a =25 c) parameter symbol min typ max units notes input capacitance c in 5 pf output capacitance c out 7 pf ac electrical characteristics (-40 c to +85 c; v cc = 5.0v 10%) parameter symbol min typ max units notes clk frequency f clk dc 10 mhz 8 width of clk pulse t ch 50 ns 8 data setup time t dc 30 ns 8 data hold time t cdh 10 ns 8 propagation delay time low to high level clock to output t plh 50 ns 8 propagation delay time high to low level t phl 50 ns 8 rst high to clock input high t cc 50 ns 8 rst low to clock input high t hlt 50 ns 8 rst inactive t rlt 125 ns 8 clk rise time, clk fall time t cr 50 ns 8 notes: 1. all voltages are referenced to ground. 2. resistor inputs cannot exceed the substrate bias voltage , vb, in the negative direction. 3. absolute linearity is used to determine wiper voltage ver sus expected voltage as determined by wiper position. device test limits 1.6 lsb. downloaded from: http:///
ds1267 10 of 12 102199 4. relative linearity is used to determine the change in v oltage between successive tap positions. device test limits 0.5 lsb. 5. typical values are for t a = 25c and nominal supply voltage. 6. -3 db cutoff frequency characteristics for the ds1267 depend on potentiometer total resistance : ds1267-010: 1 mhz; ds1267-050: 200 khz; ds1267-100: 100 khz. 7. c out is active regardless of the state of rst . 8. see figure 9(a), (b), and (c). 9. see figure 11. 10. valid at 25 c only. timing diagrams figure 9 (a) 3-wire serial interface general overview (b) start of communication transaction downloaded from: http:///
ds1267 11 of 12 102199 (c) end of communication transaction digital output load schematic figure 10 downloaded from: http:///
ds1267 12 of 12 102199 typical supply curent vs. serial clock rate figure 11 downloaded from: http:///

▲Up To Search▲

Price & Availability of DS1267S-100TR

	To Download DS1267S-100TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .